preliminary specification model LCM-60DA dc voltage range rated power output setup, rise time note.6 hold up time (typ.) voltage range note.4 frequency range power factor (typ.) efficiency (typ.) note.7 ac current (typ.) input inrush current(tye.) leakage current safety standards dali standards working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing 2 ~ 90v 2 ~ 86v 2 ~ 90v 2 ~ 67v 2 ~ 57v 2 ~ 42v 60.3w 700mvp-p 95v 73v 1000ms, 80ms / 230vac at rated power 180 ~ 295vac 254 ~ 417vdc 47 ~ 63hz 92% cold start 35a/230vac compliance to en55015, en61000-3-2 class c( 35% rated power) ; en6100 0-3-3 ? compliance to en61000-4-2,3,4,5,6,8,11, en55024, en61547 ligh t industry level (surge 2kv), criteria a -30 ~ +60 j (refer to "derating curve") 20 ~ 90% rh non-condensing -40 ~ +80 , 10 ~ 95% rh j ? j j 0.03%/ (0 ~ 50 ) 10 ~ 500hz, 2g 10min./1cycle, period for 60min. each along x, y, z axes k hrs min. mil-hdbk-217f (25 ) j 123.5*81.5*23mm (l*w*h) 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf parallel capacitor. 3. please see "dip switch table". 4. derating may be needed under low input voltage. please check the static ch aracteristics for more details. 5. the power supply is considered as a component that will be operated in combi nation with final equipment. since emc performance will be affected by th e complete installation, the final equipment manufacturers must re- qualify emc directive on the complete installation again. 6. length of set up time is measured at first cold start. turning on/off the powe r supply may lead to increase of the set up time. 7. efficiency is measured at 900ma/67v output set by dip switch. 8. no load power consumption<1.2w is measured at 180 277vac. j ~ 0.24kg 60w multiple-stage output current led power supply ?e?e ?e ?e ?e ?e ?e ?e ?e ?e ?e ?e ?e ?e output current level selectable by dip s.w.180~295vac input only built-in active pfc function protections: short circuit / over voltage / over temperature cooling by free air convection temperature compensation function by external ntc no load power consumption <1.2w@ac always on power supplies synchronization function up to 10 units 3 years warranty o fully isolated plastic case class power unit, no fg built-in dali interface and push dimming function built-in 12v/50ma auxiliary output suitable for led lighting applications ?? features : LCM-60DA series ripple & noise (max.) note.2 no load output voltage (max.) environment safety & function emc protection 16ms/230vac at rated power withstand voltage isolation resistance i/p-o/p:3.75kvac ul8750, enec en61347-1, en61347-2-13,en62384 independent appr oved iec62386-101, 102, 207 i/p-o/p:>100m ohms / 500vdc / 25 / 70% rh j file name:LCM-60DA-spec 2012-09-11 selectable current note.3 500ma 700ma 600ma 900ma 1050ma 1400ma ? 5.0% current accuracy emc immunity emc emission selv f m m 110 short circuit over voltage over temperature auxiliary power temp. compensation synchronization constant current limiting, recovers automatically after fault con dition is removed 90 10 (rth2) j ? j protection type : shut down o/p voltage, re-power on to recover please see "synchronization operation" dimming please see "dimming operation" protection type : shutdown o/p voltage, re-power on to recover 105 ~ 125v 12v @ 50ma for driving fan; tolerance 5% ? by external ntc(not provide with the power supply), please see "tempera ture compensation operation" total harmonic distortion total harmonic distortion will be lower than 20% when output loading is 75% o r higher <0.5ma / 240vac 0.3a/230vac 0.25a/277vac ripple current ? 5% pf 0.98/230vac, pf 0.96/277vac at rated power (please refer to "power f actor characteristic" curve) ? ?
preliminary mechanical specification case no. unit:mm block diagram dim+ dim- detection circuit emi filter rectifiers power switching filter & rectifiers rectifiers +v +12vaux -v i/p control o.v.p. & o.l.p. mcu pfc circuit pfc control o.l.p. o.t.p. pwm pfc fosc : 60khz pwm fosc : 80khz syn. connector(cn101/cn100):jst b2b-xh or equivalent pin no. assignment mating housing jst xhp or equivalent terminal jst sxh-001t-p0.6 or equivalent 1,3 2,4 + - terminal pin no. assignment(tb3/tb4) : pin no. pin no. 12 3 45 6 assignment assignment +12vaux. -ntc dim+ dim- -12vaux. +ntc load (%) 20 40 60 80 100 input voltage (v) 60hz 180 190 200 210 220 230 240 260 270 280 295 100 90 80 70 60 50 40 load (%) derating curve load (%) derating curve static characteristics ambient temperature ( ) j load (%) 250 load (%) (horizontal) -15 0 15 30 0 40 50 -30 60 70 file name:LCM-60DA-spec 2012-09-11 60w multiple-stage output current led power supply LCM-60DA series 2- 4.2 r 6.75 6.75 68 81.5 6.75 110 123.5 6.75 4 39.3 65.5 2- m3 7.8 23 7.8 syn. tb3/tb4 ac/l ac/n push da+ da- 12 3 4 5 6 on 654321 cn100 cn101 + vo -
preliminary efficiency (%) efficiency (%) LCM-60DA series possess superior working efficiency that up to 92% can b e reached in field applications. efficiency vs load LCM-60DA is a multiple-stage output current supply, selection of out put current through dip switch as table below. dip switch table io 500ma 600ma 700ma(factory setting) 900ma 1050ma 1400ma dip s.w. 1 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 2 on on on on on on on on on 3 on on on 4 on on 5 on 6 on on on file name:LCM-60DA-spec 2012-09-11 pf pf load (230vac input) load (230vac input) load (277vac input) load (277vac input) constant current mode constant current mode (60w) (60w) power factor characteristic 60w multiple-stage output current led power supply LCM-60DA series 0.63 0.66 0.69 0.72 0.75 0.78 0.81 0.84 0.87 0.9 0.93 0.96 0.99 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 500 600 700 900 1050 1400 50.0% 55.0% 60.0% 65.0% 70.0% 75.0% 80.0% 85.0% 90.0% 95.0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 500 600 700 900 1050 1400 0.48 0.51 0.54 0.57 0.6 0.63 0.66 0.69 0.72 0.75 0.78 0.81 0.84 0.87 0.9 0.93 0.96 0.99 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 500 600 700 900 1050 1400 40.0% 45.0% 50.0% 55.0% 60.0% 65.0% 70.0% 75.0% 80.0% 85.0% 90.0% 95.0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 500 600 700 900 1050 1400
preliminary ?e 10 drivers(max.) synchronization (1 master + 9 slaves) ?e maximum length of the cable from first driver to last driver is 15 meter. LCM-60DA (slave 2) LCM-60DA - - - - - - + + + + + + syn. da- push button ac/n ac/l da+ push ac/n ac/l syn. syn. LCM-60DA (master) LCM-60DA (slave 1) dimming operation synchronization operation ? push dim(primary side) ?e maximum number of drivers up to 10 pcs. ?e maximum length of the cable, from push button to last driver is 15 meter. ?e factory setting at 100%. ?e when the light is lower than 10% it will always dim up, or when the light output is hig her than 90% it will always dim down. warning: the pushbutton can only be connected in between the push termin al of LCM-60DA and ac/l (brown or black color). it would cause short circu it if it is connected to ac/n. ?e dali protocol including 16 groups and 64 addresses. ?e first step is fixed at 1% light output. ? dali interface(primary side) ignore <0.05 sec. to avoid reaction on ac spike short push 0.1~1 sec. push to turn on-off long push 1.5~10 sec. dimming up or down reset push >11 sec. setting light to 100% file name:LCM-60DA-spec 2012-09-11 60w multiple-stage output current led power supply LCM-60DA series
preliminary 65 70 75 80 85 90 95 100 105 55 60 65 70 75 80 85 90 95 220ko 330ko 470ko ntc derating curve 220k [ 330k [ 470k [ sensed temperature(degree) output io (%) temperature compensation operation LCM-60DA have the built-in temperature compensation function (t , i o ). by connecting a temperature sensor (ntc resistor) between the ? ?? ntc +/- terminal of LCM-60DA and the detecting point on the lighting system or the s urrounding environment, output current of LCM-60DA could be correspondingly changed to ensure the long life of led. 1.LCM-60DA can still be operated well when the ntc resistor is not connect ed and the value of output current will be the current level that you set 2. through the dip switch. ntc resistance 220k 330k 470k output current < 60 , 100% of the rated current (corresponds to the setting current level) j < 70 , 100% of the rated current (corresponds to the setting current level) j < 80 , 100% of the rated current (corresponds to the setting current level) j > 60 , output current begin to reduce, details please refer to the curve. j > 70 , output current begin to reduce, details please refer to the curve. j > 80 , output current begin to reduce, details please refer to the curve. j 3. synchronization function of the power supply will be invalid when the" t emperature compensation function" is in use . notes: 1. mw does not offer the ntc resistor and all the data above are measured by u sing thinking ttc03 series. 2. if other brands of ntc resistor is applied,please check the temperatur e curve first. file name:LCM-60DA-spec 2012-09-11 60w multiple-stage output current led power supply LCM-60DA series
|
